|
Delta-3 Series
DT-2A
Two-button Digital Transmitter
Code Setting
Instructions
DT-2A TWO-BUTTON
TRANSMITTER CODE SETTING: There are two digital switches in the DT-2A
transmitter. Code Switch “A”, is exposed by removing the battery access cover.
It is the coding switch for the LEFT button on the front of the
transmitter (Button ”A”). Code switch “B” is the coding switch for the RIGHT
button on the front of the transmitter (Button ”B”). The switch is located
behind the back cover of the transmitter. To access Coding Switch “B”, it is
necessary to remove the screw located in the middle of the back cover.
SETTING CODE SWITCH “A”
Before removing the battery
access door, loosen battery clip screw and rotate clip away from door. To open
the battery access cover and gain access to Coding Switch “a”, lift off the
small L-shaped cover by inserting your thumbnail or a small screwdriver under
either of the two slots at the edge of the case. The coding switch has eight
keys numbered 1-8.
To set a code, select any
combination of ON or OFF positions for the switch keys numbered 1-8. Use a paper
clip or other pointed object ) except a pencil or Pen) to set the keys on the
coding switch. The ON position is when the top of the switch is down.
SETTING CODE SWITCH “B”
To gain access to Coding Switch “B”, first remove the
screw in the middle of the back cover. Remove the back cover to expose the 8-key
switch.
To set a code, select any
combination of ON and OFF positions for the switch keys, in the same manner as
described for Coding Switch “A”.
CAUTION:
It is not advisable to set a code with all keys ON, OFF,
or alternating ON and OFF, because these codes are too easy to duplicate.
TRANSMITTERS CODE MUST MATCH RECEIVER CODE
Switch “A” is designed for use with a garage door opener.
The code set to Switch “A” must be identical to the code set in the receiver to
be used in conjunction with Push-button “A”.
Switch “B”, under the back cover is designed for use with
less-frequently changed codes, such as a community gate operated by Push-button
“B”. The code set into Switch “B” must be identical to the code set in the
receiver to be used in conjunction with Push-button “B”.
256 AVAILABLE CODES ON EACH SWITCH
You can select any one of 256 codes on Switch “A” and
also any one of 256 codes on switch “B”.
NOTE:
The manufacturer strongly recommends that you test your
equipment frequently. From the time of installation, it is absolutely necessary
to test the system at least once a week. It is also good practice to change the
9-volt battery every sin months.
NOTE:
The transmitter transmits continuously with button
depression. An LED lights during transmission to indicate battery operation.
LIMITED
WARRANTY
This product is warranted to the consumer against defects
in material and workmanship for one year from the date of purchase. This
warranty applies to first retail buyers of new devices. Warrantor will repair,
or at its option, replace any device it finds that requires service under the
warranty, and will return the repaired or replaced device to the consumer at the
warrantor’s cost. For warranty service and shipping instructions contact
warrantor at the address shown below. Devices must be sent to warrantor for
service at owner’s expense. The remedies provided by this warranty are
exclusive. Implied warranties under state law are to the one- year period of
this written warranty. Some states do not allow limitations on how long an
implied warranty lasts; so the above limitation may not apply to you. In order
to be protected by this warranty, save your proof of purchase and send copy with
equipment should repair be required. This warranty gives you specific legal
rights, which vary from state to state.
All products returned for warranty service require a
Return Product Authorization Number (RPM). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details.
IMPORTANT!!!
Linear radio controls provide a reliable communications
link and fill an important need in portable wireless signaling. However, there
are some limitations, which must be observed.
·
For U.S. installations only: The radios are required to comply
with FCC Rules and Regulations as Part 15 devices. As such, they have limited
transmitter power and therefore limited range.
·
A receiver cannot respond to more than one transmitted signal at a
time and may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
·
Changes or modifications to the device may VOID FCC compliance.
·
Infrequently used radio links should be tested regularly to
protect against undetected interference or fault.
·
A general knowledge of radio and its vagaries should be gained
prior to acting as a wholesale distributor or dealer, and these facts should be
communicated to the ultimate users.
|
