Wireless Keyless Entry System How To Programming Instructions for Marantec Garage Door Openers

Keypad. It can be programmed to control up to 3 garage door openers that each work on a different code, or to control one garage door opener with up to 3 different PINs. It can also be programmed to allow a temporary PIN of your choice to be stored, to provide temporary access to authorized visitors or service persons. Also an additional device (e.g. a yard light) can be controlled. For the function (Light function) an optional receiver is needed.

Other Features Include:

Wireless Installation Code Security, Anti-Tampering, and Weather-Resistant Design.

Step 1: Setting Up Your Personal Identification Number (PIN) and Transferring the Code. Your Keyless Entry System comes factory pre-programmed with 1 random code and 1 PIN. The factory pre-programmed PIN is 1-2-3-4. If you are using the remote control transmitters to operate your garage door, the transmitter code must be transferred to the Keyless Entry System from the active transmitter you are already using.

Transferring the Code for Controlling you Garage Door to the Keyless Entry System from a Transmitter:

· Open the terminal area (on side of the Keyless Entry) and connect the Keyless

Entry System to the active transmitter using the programming connector.

· Press and hold the transmitter button you use to open and close your garage door.

On the Keyless Entry System, press the ENTER button. The keypad illumination turns on.

· Input any new 4-digit PIN of your choice. Press the ENTER button again. Keep the transmitter button pressed until the LED on the Keyless Entry System blinks rapidly.

· The Keyless Entry System has now learned the code from the transmitter, and stored it

under the PIN that you entered. Remove the programming connector and close the

terminal area.

Transferring a new Code for the Light Function to the Keyless Entry System from a Transmitter:

The light Function is factory pre-programmed with its own code. An existing transmitter code could be transferred to the Light Function.

· Open the terminal area (on the side of the Keyless Entry) and connect the Keyless Entry

System to the active transmitter using the programming connector.

· Press and hold the transmitter button you choose to activate any other device. On the Keyless Entry System, press the ENTER button. The keypad illumination turns on.

· Press the LIGHT button. Press the ENTER button again. Keep the transmitter button pressed until the LED on the Keyless Entry System blinks rapidly.

· The Keyless Entry System has now learned the new code for the light function from the transmitter. Remove the programming connector and close the terminal area.

STEP 2: KEYLESS ENTRY SYSTEM MOUNTING.

· Choose location for mounting your Keyless Entry System.

· Using mounting holes at the top and bottom of the spacer as a guide, mark hole locations and then drill two 1/16” pilot holes.

· Secure spacer to the mounting surface with the (2) 1/8” X 1-3/8” screws provided. For mounting surfaces that are not made of wood, alternate anchoring means may be needed.

· Snap the Keyless Entry System into the spacer.

· Turn clockwise the key on the bottom of the spacer using a coin to lock the Keyless Entry System.

STEP 3: Using Keyless Entry System.

Switching On the Keypad Illumination

· Press the LIGHT button. The keypad illumination turns on for 5 seconds.

Opening and Closing a Garage Door

· Enter 4-digit PIN (programmed in Step 1) followed by pressing the ENTER button. Garage door will being moving.

· Keyless Entry System will remain active and LED will flash for approximately 18 seconds after pressing the ENTER button. During this time, the garage door can be stopped by pressing any button (except the LIGHT button).

· Under certain conditions, your garage door may require constant pressing of a button to operate. In this case, enter your 4-digit PIN then press and hold the ENTER button. Garage door will run as long as the ENTER button is held.

NOTE: If a PIN with more than 4 digits is entered, the Keyless Entry System considers the last 4 digits. If an invalid PIN is entered 3 times in a row, the Keyless Entry System automatically shuts off to prevent tampering or unauthorized use. After 2 minutes, the Keyless Entry System can be used again.

Light Function (Switching any other devices)

· To turn on any other device (e.g. a yard light) press the LIGHT button followed by pressing the ENTER button.

· To turn off any other device (e.g. a yard light) press the LIGHT button followed by pressing the ENTER button once again.

Storing more than 1 Code to Control more than 1 Garage Door Opener

· The Keyless Entry System may be used to control up to 3 different garage door openers, each with a different code.

· For each of the 3 codes, follow the same steps as shown in Step 1, with one exception you must enter a different PIN for each code. Each code requires a unique PIN.

· To use the Keyless Entry System to open or close a specific door, simply enter the corresponding PIN for that door followed by pressing the ENTER button.

Storing more than 1 PIN for Same Code

· It is possible to store in addition to the pre-programmed PIN up to 2 other PINs for the same code for use by different individuals.

· For each separate PIN, follow the same steps as shown in Step 1. Repeat the procedure for each PIN, using the same transmitter each time. This will store the same code under 3 different PINs.

Storing a Temporary PIN

· A temporary PIN can be stored which will permit operator for 3 times only.

· Press and hold “button 1” on the keypad for 3 seconds until the LED on keypad blinks rapidly. Enter your original PIN followed by the ENTER button.

· Enter a temporary 4-digit PIN of your choice followed by the ENTER button.

· The LED on the keypad will illuminate for 2 seconds, then the Keyless Entry System will shut off and the keypad illumination will go out. Keyless entry System is now ready for use again.

· To use Keyless Entry System with the newly stored temporary PIN, enter the 4-digit temporary PIN followed by pressing the ENTER button. This can be done 3 times, after which the temporary PIN will be automatically erased.

Changing the PIN

· Press and hold “button 0” on the keypad for 3 seconds until the LED on the keypad blinks rapidly.

· Enter the PIN which is to be changed followed by pressing the ENTER button.

· Enter the new 4-digit PIN followed by pressing the ENTER button. The LED on the keypad will turn on (no flashing) for 2 seconds.

· The Keyless Entry System is now ready for use again with the new pin (Old PIN is no longer valid).

Clearing the Memory

· Press and hold the LIGHT button on the keypad for 3 seconds until the LED on the keypad blinks rapidly.

· Enter the PIN 9-9-9-9.

· Release LIGHT button. The memory is cleared. The LED on the keypad will illuminate for 2 seconds.

NOTE: After cleaning the memory, the Keyless Entry System is programmed with 1 random code and the PIN 1-2-3-4.

Replacing the Batteries

· Turn counterclockwise the key on the bottom of the spacer and remove the Keyless Entry System from the spacer.

· Release the back plate of the Keyless Entry System.

· Remove old batteries.

· Replace with 2 new 3V batteries, CR 2032. Match polarity designation. Test operability. (Keyless Entry System is designed to remember all previously programmed codes and PINs while battery is being replaced).

· Replace the back plate.

For protection of keypad, keep cover closed when not in use.

Payment Processing

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981. Providing excellent customer service and assistance for over 25 years. We are a discount reseller of garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community. We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

Copyright © 2011 garage-door-openers.us No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.