Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists Sales 1-407-483-7966

 

 Home

Contact Us

About Us

Shipping

Follow us on Facebook

Click for the BBB Business Review of this Garage Doors & Openers 
in Kissimmee FL

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

 TriCode®

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

361LM, 362LM, 363LM Specialty Remote Controls

Passport Remotes

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Wireless Intercoms

Vehicle Alert Systems

Driveway Alert by Optex

Garage Accessories
Sky Link Security Center
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Allstar Allister Pulsar MVP Garage Door Opener Remote Control Transmitter How to Coding Instructions

MVP QUIK-CODE TRANSMITTER

Installation Instructions for Garage Door and Gate Openers

 WARNING—DISCONNECT POWER TO OPERATOR BEFORE ANY INSTALLATION OR REPAIR.  FOLLOW ALL INSTRUCTIONS PROVIDED BY THE MANUFACTURER OF YOUR OPERATOR.

Keep transmitters and remote controls out of the reach of children.  Do not let children play with or use the transmitter or remote controls.  Unexpected door operations can cause personal injury or property damage.  Do not place transmitter where the buttons can be accidentally or unintentionally activated.

***Proper installation of your radio controls will assure years of trouble-free operation.

READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE STARTING INSTALLATION

Your new radio controls are designed to remotely operate garage door and gate openers.  The transmitter permits the user to select one of 19683 possible codes for each one of the three buttons.  The radio frequency of the remote controls is fixed and tuned to the factory; adjustments are not required and should not be attempted by the end user. 

The MVP Quik-Code transmitter is based on the latest technology and provides maximum performance and maximum flexibility.  Since each button of the Quik-Code transmitter may be programmed with a unique code, it is possible to control a single operator or a group of operators at one location or at multiple locations. 

The Quik-Code transmitter may be mounted on a visor using the metal visor clip (included) or attached to a key-chain with the built-in attachment.

**WARNING**

Keep transmitters and remote controls out of the reach of children.  Do not let children play with or use the transmitter or remote controls.  Unexpected door operations can cause personal injury or property damage.  Do not place transmitter where the buttons can be accidentally or unintentionally activated.

RADIO CONTROL COMPATIBILITY

In addition to the Allstar MVP and Challenger E-Series Residential Garage Door Opener, the MVP Quik-Code transmitter is designed to be compatible with all Allstar MVP series receivers.

PROGRAMMING QUIK-CODE TRANSMITTERS

Programming the Allstar MVP Quik-Code transmitter is done as follows:

1.  Put the transmitter in program mode. 

2.   Select the button you wish to use.

3.  Enter your 9 digit code.

After your code is confirmed, repeat the procedure for the remaining buttons.

PUT THE TRANSMITTER IN PROGRAM MODE

Step 1:  FIRST, press and hold the + button.  The Red LED will turn on.  NEXT, while continuing to hold the + button, press and hold the – button.  Continue to hold both buttons until the LED starts to blink (approximately 5 seconds).  RELEASE BOTH BUTTONS WHILE THE LED IS BLINKING.  The LED will blink two times and then remain on to confirm you are in programming mode. 

SELECT THE BUTTON YOU WISH TO USE

Step 2:  While the LED is on, PRESS THE BUTTON YOU WISH TO USE.  The LED will blink off once and then remain on.

ENTER YOUR 9 DIGIT CODE

Step 3:  ENTER THE 9-DIGIT CODE from the table by pressing the buttons that correspond with the entries in the table.

CONFIRM ENTRY

After the 9-digit code is entered, the LED WILL BLINK TWICE TO CONFIRM a valid code and remain off.

PROGRAM REMAINING BUTTONS

Repeat the procedure for the remaining buttons.

EXPRESS CODING

EXPRESS CODING WILL PROGRAM ALL 3 BUTTONS AT ONE TIME.

To use Express Code to program all the buttons at the same time select the “+” button in Step 2 and end the 9 digit code entry in Step 3 with a “+”.  This will code all three buttons in one programming step.

**IF THE LED GOES OUT THE PROGRAMMING MODE HAS TIMED OUT AND YOU WILL NEED TO START OVER.

WARNING

RADIO CONTROLS ARE PROHIBITED FROM PROVIDING CONSTANT CONTACT CLOSURE WHEN INSTALLED ON THE PUSH BUTTON INPUTS OF RESIDENTIAL GARAGE DOOR OPENERS THAT ARE PROVIDED WITH MONITORED SAFETY SYSTEMS.

            LEARNING TRANSMITTER CODES

The MVP and Challenger door operators and MVP receivers are capable of learning up to 8 different transmitter codes.  Multiple transmitters with the same code may be used and only requires the code from a single transmitter to be learned.   

PROGRAMMING THE MVP DOOR OPERATOR

Step 1:  Momentarily press and release the Program button on the deluxe wall station.  The RED LED and worklight on the operator will turn on.

Step 2:  Using a programmed transmitter, press the desired transmitter button.  When the receiver learns the transmitter code, the LED and worklight will turn off.

Step 3:  Repeat to add additional transmitters with different codes. 

NOTE:  If the LED and worklight blink press and hold program button for 5 seconds to clear memory and start over.  If the LED and worklight remain on when you transmit press and hold program button for 5 seconds to clear memory and start over.

PROGRAMMING MVP RECEIVERS

Step 1:  Momentarily press and release the Program button.  The LED will turn on.

Step 2:  Using a programmed transmitter, press the desired transmitter button.  When the receiver learns the transmitter code, the LED will turn off.

Step 3:  Repeat to add additional transmitters with different codes.

ERASING THE RECEIVER’S MEMORY

Step 1:  Press and HOLD the Program button.  The indicator LED will turn on.

Step 2:  When the LED turns off (after approximately 5 seconds), release the Learn button.  All transmitters and keypad codes have been erased.

PROGRAMMING THE CHALLENGER DOOR OPERATOR

Step 1:  Momentarily press and release the Program button on the back panel of the operator.  The RED LED and worklight on the operator will turn on.

Step 2:  Using a programmed transmitter, press the desired transmitter button.  When the receiver learns the transmitter code, the LED and worklight will turn off.

Step 3:  Repeat to add additional transmitter with different codes.

NOTE:  If the LED and worklight blink press and hold program button for 5 seconds to clear memory and start over.  If the LED and worklight remain on when you transmit press and hold program button for 5 seconds to clear memory and start over.

INSTALLING THE TRANSMITTER

            The transmitter is supplied with a metal clip which may be used to attach the unit to a sun visor.  If the clip is used, slide it into the recess provided on the back of the transmitter case until the snaps on the case fit around the clip.  If the transmitter is installed in a pocket in your car, follow all the manufacturer’s instructions.  Improper installation may cause intermittent transmitter operation which can result in unexpected door operations.

 WARNING—DISCONNECT POWER TO OPERATOR BEFORE ANY INSTALLATION OR REPAIR.  FOLLOW ALL INSTRUCTIONS PROVIDED BY THE MANUFACTURER OF YOUR OPERATOR.

BATTERY REPLACEMENT

The MVP Quik-Code transmitter is provided with two factory installed 3-vold batteries which should be replaced after two years of normal use.  The transmitter code is retained in permanent memory and will not be lose during battery replacement.  To replace the batteries, remove the back of the case with a small screwdriver.  Carefully slip the batteries out of the holders and replace with fresh CR2032 3-volt batteries.  The “+” on the batteries must point away from the circuit board.  Replace the back of the cover and resume normal use. 

 

OPERATIONAL CHECK

After installing your received and transmitter, check the operation of your radio controls by moving approximately 45 feet back from the garage door, then press the transmitter button.  Operation at this distance should be reliable.  However, environmental conditions and the location of the transmitter and receiver will affect distance.

*If the distance is inadequate check the batter and replace if necessary.

*To maximize the operating distance move the transmitter to a different location in the car until a satisfactory distance is achieved.  Vanity mirrors on sun visors will affect performance.

*If the receiver is in the proximity of a metal beam or other obstruction it may be necessary to relocate the receiver to increase the operating range.

*If multiple receivers are mounted closer than 15 feet, blocking and interference may occur.  Move the receivers farther apart.

*If system does not work at any distance, check that the receiver terminals are connected to the proper operator terminals.

*If the HomeLink transmitter does not activate the operator or distance is inadequate, verify proper operation using the hand-held transmitter.  Contact HomeLink system provider for help with configuring the HomeLink transmitter and to resolve distance problems when using the HomeLink system.

Payment Processing

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

3050 Dyer Blvd Suite 554 (hours by appt only)

Kissimmee, FL   34741

1-407-483-7966

1-407-507-4704   Fax

Garage Door and Garage Door Openers

Copyright © 2014 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.